Rode VideoMic GO On-Camera Shotgun Microphone
Rode VideoMic GO On-Camera Shotgun Microphone

Rode VideoMic GO On-Camera Shotgun Microphone

rode

SSK # RODE-VMR-GO

Discontinued
1 Year Rode Warranty
RM329.00
RM339.00

Shopping Point 1.645 = RM1.65

Key Features

  • Lightweight at Only 2.6 Ounces
  • Rycote Lyre Suspension System
  • Requires 2.5V Camera Plug-in Power
  • Integrated Shoe Mount with 3/8" Thread
  • 3.5mm Mini-Jack Output
  • Foam Windshield Included
  • Reinforced ABS Construction
  • 3.5mm Coiled Output Cable Included

Longer than Rode's VideoMicro and with a narrower pickup pattern, the Rode VideoMic GO camera-mount shotgun microphone offers enhanced off-axis rejection for tighter directionality. Like the VideoMicro, it runs on plug-in power and has no controls or switches, making it well suited for mobile journalists, vloggers, and run-and-gun shooters in a hurry.

This compact and lightweight shotgun microphone features an integrated shockmount that mounts directly to your DSLR, mirrorless, or video camera and reduces noise from vibrations and camera handling. The windscreen design reduces wind noise, making it well suited for outdoor shoots. The detachable coiled 3.5mm TRS cable ensures easy hookup to your camera, and the dual-mono output means that no channel selection is necessary on your recording device.

Shotgun Mic with Directional Sound Pickup

Whereas most built-in camera microphones pick up sound from all directions, this microphone utilizes a supercardioid polar pattern to focus on sound in front of it while attenuating sound from the sides and rear. Its active electronics and directional condenser element deliver more detailed audio than the mics typically found in cameras and portable recorders.

Easy Hookup to Camera

A detachable coiled 3.5mm cable is supplied for fast hookup to your camera. The cable is wired in a dual-mono configuration, ensuring that the mic signal is sent identically to both input channels of your camera or portable recorder.

Runs on Plug-In Power

No batteries are required to operate the VideoMic GO. Just connect the microphone to your camera or recorder, enable plug-in power on the device, and forget about swapping or charging batteries.

Integrated Shockmount Inhibits Vibrations

Understanding that the rubber bands used in many shockmounts can snap and stretch, Rode chose to integrate a rugged Rycote Lyre suspension-style shockmount. This simplifies setup of the mic and inhibits the transfer of vibrations from the camera. Plus, the bottom of the shockmount features a camera shoe mount with a 3/8" thread, ensuring easy attachment to your camera or a boompole such as Rode's Micro Boompole (available separately).

Windscreen Minimizes Wind Noise

The VideoMic GO has a foam windscreen to reduce unwanted wind noise from breezes, fans, heaters, and air conditioners. For maximum reduction of wind noise in outdoor environments, consider a furry windshield such as the Rode DeadCat GO (available separately).

Connectivity Options

Expand the microphone's device compatibility with Rode accessories such as the SC4, SC7, and VXLR+ (all available separately). With either the SC4 or SC7, you can connect the VideoMic GO directly to a smartphone or tablet equipped with a 3.5mm TRRS jack. The VXLR+ adapter is the ideal solution when you want to record the VideoMic GO to a camcorder or mixer that has XLR inputs.

Rode VideoMic GO Specs

Microphone
Form Factor Stand/Boom Mount
Sound Field Mono
Operating Principle Line Gradient
Capsule Electret Condenser
Diaphragm 0.5" / 12.70 mm
Polar Pattern Supercardioid
Orientation End Address
Circuitry Solid-State (JFET)
Pad None
High-Pass Filter None
Tone Adjustment None
Indicators None
On-Board Controls None
Windscreen Foam (Included)
Performance
Frequency Range 100 Hz to 16 kHz
Maximum SPL 120 dB SPL (1 kHz, 1% THD, 1-Kilohm Load)
Off-Axis Rejection 4 dB at 60°
16 dB at 120°
12 dB at 180°
Sensitivity -35 dBV/Pa at 1 kHz
Dynamic Range 96 dB
Signal-to-Noise Ratio 60 dB A-Weighted
Equivalent Noise Level 34 dB A-Weighted
Connectivity
Output Connectors (Analog) 1 x 1/8" / 3.5 mm TRS
Cable Length 7.87 to 13.78" / 20 to 35 cm
Number of Conductors 2
Wireless Connectivity None
Power
Operating Voltage 2.5 V
Operating Current Consumption 330 µA (Plug-In Power)
Physical
Color Black
Mounting 3/8"-16 Female, Camera-Mount, Shockmount (with Included Hardware)
Construction Material ABS
Dimensions ø: 3.11 x L: 6.57" / ø: 79 x L: 167 mm
Weight 2.58 oz / 73 g
Packaging Info
Package Weight 0.43 lb
Box Dimensions (LxWxH) 9.95 x 4.9 x 2.9"

 

RodeVideoMic GO On-Camera Shotgun Microphone
  • Foam Windshield
  • 3.5mm Dual Mono Output Cable (7.9")

Reviews Rode VideoMic GO On-Camera Shotgun Microphone

Login to leave review.
Login to get access to Q&A

SOLD
Rode VideoMic GO On-Camera Shotgun Microphone
Discontinued
Rode VideoMic GO On-Camera Shotgun Microphone
0

RM329.00 RM339.00