DJI Spreading Wings S1000+ with Z15-5DIII (HD) Gimbal and A2 Flight Controller (for Canon EOS 5D Mark III)
Featuring a removable upper center board for easier installation of flight electronics as well as a redesigned power distribution system, the
Spreading Wings S1000+ with Z15-5DIII (HD) Gimbal and A2 Flight Controller from
DJI continues the legacy of the original S1000. The S1000+ is a collapsible, eight-propeller RC helicopter designed to carry a DSLR or similar-sized camera. With a 24-pound maximum takeoff weight, it is intended to serve as a camera platform, allowing professional videographers and photographers to add dynamic aerial shots to their productions.
The bundle features the DJI A2 flight control system, a collection of hardware components that control mixing, regulate power, provide sensor data, and include a 2.4 GHz DR16 receiver. The flight control system features attitude and GPS attitude flight modes, offering the pilot varying degrees of autopilot intervention depending on skill level and preference. In GPS mode it is possible to hover in a fixed position, which is ideal for capturing static video shots. In attitude mode, the flight controller will use IMU data to keep the aircraft stable, but when hovering it may drift due to inertia or wind currents. The A2 also features return to home, Intelligent Orientation Control, and other features made possible thanks to computerized, GPU-based flight control. The built-in receiver is compatible with Futaba FASST series and DJI DESST series transmitters (radio controllers). Third-party receivers are also supported.
For stabilizing and moving the camera in flight, this bundle features the Zenmuse Z15-5D (HD), a 3-axis gimbal specifically for the Canon 5D Mark III DSLR. The airframe features a dampened gimbal mounting bracket with a low mounting position. Additionally, the landing gear can be raised, allowing an unobstructed 360 degrees of visibility. This the HD version of the gimbal which means there is an HDMI signal relay through it for connecting the Lightbridge Air Unit. For the moment the gimbal is calibrated specifically for use with the Canon EF 24 mm f/2.8 IS USM lens. However, support for addition lenses is expected to be added in the future.
The S1000 is designed to power 6S lithium-polymer batteries. It will support capacities between 10,000 and 20,000mAh, and requires a discharge rate of at least 15C. With a 15,000mAh battery and a take-off weight of 21 pounds, it is estimated to fly approximately 15 minutes.
Note: This aircraft not ready-to-fly (RTF): Assembly is required, and batteries and a transmitter are not included. Please refer to the S1000+ User Guide for details of required hardware and installation instructions.
DJI Spreading Wings S1000+ Professional Octocopter
Takeoff Weight | 13.2 lb / 6 kg to 24.2 lb / 11 kg |
Stator Size | 1.6 x 0.6" / 41 x 14 mm |
Motor Velocity Constant | KV: 400 rpm/V |
Maximum Power | 500 W |
Weight | With Cooling Fan: 5.6 oz / 158 g |
Working Current | 40 A |
Working Voltage | 6S LiPo |
Signal Frequency | 30 to 450 Hz |
Drive PWM Frequency | 8 kHz |
Weight | 1.2 oz / 35 g |
Size | 15 x 5" / 38.1 x 12.7 cm |
Weight | 0.5 oz / 13 g |
Diagonal Wheelbase | 41.1" / 1045 mm |
Frame Arm Length | 15.2" / 386 mm |
Center Frame Diameter | 13.3" / 337 mm |
Center Frame Weight | With Landing Gear Mounting Base, Servos: 3.3 lb / 1.5 kg |
Landing Gear Size | 18.1 x 20.1 x 12" / 460 x 511 x 305 mm |
Compatibility | A2 or WooKong-M |
Gain Value Settings | For A2 Flight Controller Basic: Roll 120%, Pitch 120%, Yaw 120% Attitude: Roll 170%, Pitch 170%, Vertical 120%
For WooKong-M Flight Controller Basic: Roll 130%, Pitch 130%, Yaw 120% Attitude: Roll 180%, Pitch 180%, Vertical 120% |
Power Requirements | Lithium-Polymer (LiPo): |
Power Consumption | Maximum: 4000 W Hovering: 1500 W at 20.9 lb / 9.5 kg takeoff weight |
Operating Temperature | 14 to 104°F / -10 to 40°C |
Weight | 9.7 lb / 4.4 kg |
DJI A2 Flight Control System for Multi-Rotor Aircraft
Supported ESC Output | 400 Hz refresh frequency |
Supported Transmitters | With Built-in Receiver: Futaba FASST series and DJI DESST series |
Supported External Receivers | Futaba S-Bus, S-Bus2, DSM2 |
Other DJI Products Supported | Z15, H3-2D, iOSD, 2.4G Bluetooth Data Link, and S800 EVO |
Hovering Accuracy (GPS Mode) | Vertical: ±1.6' / 0.5 m Horizontal: ±4.9' / 1.5 m |
Maximum Wind Resistance | < 26.2 fps (8 m/s) / 17.9 mph (28.8 km/h) |
Maximum Yaw Angular Velocity | 150 deg/s |
Maximum Tilt Angle | 35° |
Ascent/Descent | ±19.7 fps / 6 m/s |
Power Requirements | Maximum: 5 W Typical: 0.3 A at 12.5 V |
System Requirements | Assistant Software: Windows 8, 7, or XP SP3 -- 32 or 64-bit |
Operating Temperature | 23 to 140°F / -5 to 60°C |
Dimensions | Flight Controller: 2.1 x 1.5 x 0.6" / 54 x 39 x 14.9 mm IMU: 1.6 x 1.2 x 1" / 41.3 x 30.5 x 26.3 mm GPS-Compass Pro: 2.4" (diameter) x 0.6" / 62 mm (diameter) x 14.3 mm LED-BTU-I: 1.2 x 1.2 x 0.3" / 30 x 30 x 7.9 mm PMU: 39.5mm x 27.6mm x 9.8mm |
Weight | Overall: 7.9 oz / 224 g |
DJI Zenmuse Z15-5D III (HD) 3-Axis Gimbal for Canon 5D Mark III
Supported Camera | Canon EOS 5D Mark III only |
Supported Lens | Canon EF 24mm f/2.8 IS USM |
Control Requirements | At least 4 spare receiver channels S-Bus/PPM receiver supported |
Software Requirements | For Assistant Software: Windows 8, 7, XP SP3 -- 32 or 64-bit |
Working Current | Static Current: 200 mA at 25 V Dynamic Current: 400 mA at 25 V Locked-Rotor Current: 4 A at 25 V |
GCU BEC Output | 10 A at 12 V |
Transmit Power | GCU Wireless Video Transmission: 1 A at 12 V |
Controlled Angle Accuracy | ±0.02° |
Maximum Controlled Rotation Speed | Pan Axis: ±90°/s Tilt Axis: ±130°/s Roll Axis ±30°/s |
Controlled Rotation Range | Pan Axis Control: ±360° continuous rotation Tilt Axis Control: +15° / -120° Roll Axis Control: ±25° |
Load Weight (Reference Value) | 5.9 lb (2.7 kg) with 5D MARK III, SD card, battery, and Canon EF 24mm f/2.8 IS USM lens |
Power Requirements | GCU: 4S to 12 S LiPo (6S recommended for S1000) |
Operating Temperature | 14 to 122°F (-10 to 50°C) |
Dimensions | Gimbal: 11.1 x 9.5 x 8.7" (281 x 242 x 222 mm) GCU: 2.5 x 1.4 x 0.8" (64.2 x 34.1 x 19.5 mm) |
Weight | Gimbal: 3.4 lb (1.5 kg) GCU: 2.2 oz (63 g) |
- LED-BTU-I LED Bluetooth Indicator for A2 Flight Control System
- MC for A2 Flight Control System
- PMU for A2 Flight Control System
- GPS Bracket for A2 Flight Control System
- IMU Module for A2 Flight Control System
- GPS-PRO Module for A2 Flight Control System
- Gimbal Control Unit (GCU)
- Lens Retaining Ring
- 4 x Mounting Bracket
- Mounting Board for Receiver
- Cable Clamp
- 2 x Camera Mount Screw
- Lens Retaining Screw
- Screw Package
- Screw Package
- 2 x 10-Pin to 9-Pin Cable
- 7-Pin Cable
- 2 x 8-Pin to 6-Pin Cable
- Servo Cable Package
- AV Video Power Cable
- iOSD Mark II Cable
- Micro-USB Cable
- CAN-Bus Cable
- Spare Package
Loading ...
Login to get access to Q&A
Reviews DJI Spreading Wings S1000+ with Z15-5DIII (HD) Gimbal and A2 Flight Controller (for Canon EOS 5D Mark III)